Carlton 2518 Manual del operador descargar pdf (Pagina 26)

F:\data\John\Docs\Machine Docs\Machine Specs\2518 Apache SPECS 140 Deere.DOC

Carlton Apache 2518 Specifications

General: Hydraulic System:

Weight: 9300 Pounds Hyd Pump Displcmnt: 1.5 in cu/rev total from 2 pumps

Length: 211 inches Hyd Pump Drv Systm:Direct Drive off Engine Mount

Height: 100 inches Flow: 16 GPM Total Tandem Systems

Tires: 245/70R17.5 Ld Rng J 6005 # @125 PSI System Relief: 2500 PSI

Axle: Dexter Torflex 10,000 Pound Cap Oil Tank Capacity: 18 Gallons

Brakes: Electric with Breakaway Switch Oil Type: AW32

Hitch: Five Inch Height Adjustable Pintle Valve: DO5 Electric Solonoid

Fuel Capacity: 35 Gallons Hose: 16,000 PSI Burst - Exceeds SAE 100R2

Battery: 29HVD 650 CCA Oil Filter: 10 Micron Return with Suction Strainer

Jack Stand: 10000 # Cap Screw Type Swing Up

Engine: Drive System:

Manufacturer: John Deere Engine Sheave: 6/5V8.5

Number of Cylinders: Four Jackshaft Sheave: 6/5V18.7

Bore: 4.19 Inches (106 mm) Drive Belt: 6/5V1800

Stroke: 5.0 Inches(127 mm) Cutter Head Shaft: 3 ½ inches

Displacement: 276 Cubic Inches (4.5L)

Maximum RPM: 2400 RPM Feed System:

Horsepower: 140HP

Torque: 367 Ft Lbs (498 NM) Feed Motors: 46 In Cu Top 32 In Cu Bottom

Cooling Medium: Liquid Water/Antifreeze Mixture Flow: Separate Systems for Top/Btm Feed

Air Cleaner: Two Stage Dry Type Hydraulic Drive: Live – Driven off engine

Oil Filter: Full Flow Spin On Autofeed: Reversing, Digital, Fully Adjustable

Oil Capacity: 13 Quarts Feed Rate: 100 Feet Per Minute

Oil Type: John Deere Feed Rollers: Top: 15 ¾” Dia Bottom: 10 ½” Dia

Electrical: 12 Volt Springs: Two 30” Tight Wound Powder Coated

Gauges: Powerview Feed Pivot Bearings: Two 2” Tapered Roller

Clutch: Twin Disk 11 ½” Over Center Lift Cylinders: Two 2” x 18” with 1” attachments

Discharge: Crank Adjustable Swivel and Height

Bearings: Frame:

Drum Bearings: 2 15/16 inches Tapered Roller Main Trailer Tongue: 3”x 6” with 3/8” wall

Feed Roller Bearings: 2 inches Ball Bearing Main Trailer Frame: 2”x6” with 3/16” wall

Drum Shaft: 3 ½ inches Telescoping Tongue: N/A

Feed Roller Shaft: 2 inches Engine Channel Mnts: 4” Channel with 5/16”

web

Infeed Chute: 3/16” with 2”x2”x1/4” tube frame

Infeed Tray: 1/4” Plate w 2”x2” and 2” x 4” Tube

Chipper Drum: Folding Tray Lock: N/A

Discharge Chute: 12 gauge

Drum Diameter: 37 inches Discharge Lock: ¾” Spring Loaded Pin

Drum Width w/Fans: 31 3/4 inches Fuel Tank: 10 gauge with baffles rubber mtd

Drum Balance: Precision High Speed Balanced Hydraulic Tank: 10 gauge with baffles rubber mtd

Drum Speed: 1160 RPM Battery Box: 10 gauge - lockable

Number of Knives: 4 Fenders: 3/16” checker plate

Knife Dimensions: 12 5/16” x 5 ½” x 5/8” Feeder Bar: 1 ½” OD x 1/8” wall - removable

Anvil: 5 7/8” x 24 ¾” x ½” AR400 Radiator Guards: N/A

Drum Fans: 20 ¼” x 3” x 10” Light Brackets: 3/16” with hidden wiring

Hitch Plate: ¾” Plate adjustable 5” Up/Down

Cutting Dimensions:

Throat Opening: 18” x 25”

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 198 199

Comentarios a estos manuales

Sin comentarios

Carlton 2518 Manual del operador Pagina 26

Comentarios a estos manuales