Carlton 1712 Manual del operador descargar pdf (Pagina 157)

Product Features

• No need to pull the hubs to repack the bearings OR replace the seals when checking the

brakes.

• Pre-set adjustment means installation is easy and human error is virtually eliminated in

bearing adjustment.

• Pre-lubricated at the bearing factory providing resistance to contamination.

• Sealed for life, which means increased durability and reliability and no more bearing

maintenance.

• 5 year or 100,000 mile warranty against defects in material and workmanship.

1 2 ... 152 153 154 155 156 157 158 159 160 161 162 163 164 165

12” Disk Style Brush Chipper 1
CALIFORNIA 3
Proposition 65 Warning 3
IMPORTANT NOTICE 21
Warranty Validation Form 23
® Chipper 27
® also reserves the right to 28
We Pride Ourselves 29
SAFETY FIRST ALWAYS! 31
CUTTER DISK 33
SAFETY: 36
HITCH & HITCH BOLTS 38
CUTTER DISK HOOD HINGE 39
HOOD PIN & PADLOCK 39
CHIPPED KNIFE 39
ANVIL WORKING EDGE 40
® Starplex II 42
BYPASS SWITCH 43
VOLTAGE METER 43
OIL PRESSURE 43
ENGINE TEMPERATURE 43
® monitors the 44
® control is 44
® control 44
® manual 44
LIFT CYLINDER 48
LIFT CONTROL VALVE 48
STAND ALONE OPERATION 49
FRONT JACK STAND 49
HYDRAULIC WINCH 52
CONTROL VALVE 52
SELECTOR VALVE 52
ALWAYS WIND ROPE 53
UNDER THE WINCH 53
CONNECT LIGHTS 55
INFEED TRAY LOCK PIN 56
IN STORAGE POSITION 56
(ONE ON EACH SIDE OF 56
CHIPPER) 56
SPRING LOCK PIN 56
SPRING LOCK PIN 58
ENGINE OPTION 60
AUTO-FEED® ONAUTO-FEED® OFF 62
AND BUTT END FIRST 64
LEVER 2 68
LEVER 1 68
WINCH CONTROL VALVE 69
(IF EQUIPPED) 69
SHUT DOWN PROCEDURES 70
BOTH SIDES OF INFEED CHUTE 71
ROTATE CHUTE 71
RADIATOR SCREEN 73
CLEAN FROM THIS SIDE 73
RADIATOR FAN 73
ENGINE OIL FILTER 73
MAIN FILTER SAFETY FILTER 73
COOLANT FILLER CAP 74
COOLANT TANK COVER 74
ON TOP OF ENGINE 74
FUEL FILTER 74
FEED CONTROL LINKAGE 75
® Axles supplied in this 78
 Starplex II grease 79
HYDRAULICS 85
® STARPLEX II 90
CLUTCH ENGAGEMENT 94
END OF THE CROSS-SHAFT 95
REMOVE NAMEPLATE 95
ADJUSTING RING NOTCH 95
ADJUSTMENT LOCK 95
CUTTER SYSTEM 100
BELT TENSION 107
ENGINE SLIDE BOLT 108
INSIDE JAM NUT 108
OUTSIDE JAM NUT 108
OUTSIDE JAM 110
INSIDE JAM 110
LOCATION ON SHAFT 112
BEFORE REMOVING 112
MARK BUSHING 112
FEED WHEEL MOTOR 114
6-WAY PLUG DESCRIPTION 119
COLOR CODES 119
Carlton 123
IN (GND) B 143
2. Operating 144
6. Setting 148
Auto-FeedReverse 150
0.5 sec 0.5 sec 0.5 sec 151
7. Technical features 152
CAUTION 155
Product Features 157
WINCH INFORMATION 161

Comentarios a estos manuales

Sin comentarios

Carlton 1712 Manual del operador Pagina 157

Comentarios a estos manuales

Relacionado con productos y manuales para Trituradoras De Jardín Carlton 1712